𝔍为贻误手持打标机根据生存期，思想进步传奇装备根据率和无缺率，减缩缺陷率。现将我大公司手持打标机平常人保护的及养护常识知识与宗师介绍。
𝓰In order to prolong the service life of the jet printer, improve the utilization rate and intact rate of the equipment, and reduce the failure rate. Now we share our daily maintenance and maintenance knowledge with you.
一、喷码机平常利用注重事变：
1. Notices for the daily use of jet printers:
🍰1、因手持激光打码机用的吸塑油和精浓剂很是轻而易举熄火，言于须在伟大露风处安抚手持激光打码机，远离明火、火花和消除静电。
🌺1. Because the ink and diluent used in the jet printer are very easy to burn, it is necessary to place the jet printer in a well-ventilated place, away from fire, flame and static electricity.
2、不可存留吸塑油、洗濯剂泡发过的碎布和碎纸带在打码机旁。
♚2. Do not leave any ink, cloth and paper pieces soaked in detergent beside the printer.
3、 禁止在喷码器四个星期喝酒，应吊件“劝解炊火”和“易燃物吸塑油”箭头在喷码器四个星期。
ꦯ3. Smoking is strictly prohibited near the printer. The signs of "No Fireworks" and "Flammable Ink" should be hung near the printer.
4、在激光打码机周边拟定二防氧化碳灭武器图片（对比远距离10米）。
ꦚ4. Place a carbon dioxide fire extinguisher near the jet printer (the longest distance is 10 meters).
二、喷码交流接触器气毗连注重细节事变
⛄II. Notices for Electrical Connection of Jet Coder
💃1、 收到220V单项工程交流开关电源适配器（含地线），必需使用原机交流开关电源适配器线，毗连到牢固性的、仪器有地线的交流开关电源适配器电源插座上。
🍰1. When connected to 220V single power supply (including ground wire), the original power supply cable must be used and connected to a fixed power socket with ground wire.
𓄧2、 地线的毗连应该遵从有关划分。倘若地线干仗较差，有就能够生成打码机显卡的受到破坏或诱发别人卧底风险隐患。
🧔2. The connection of ground wires must comply with the relevant regulations of the state. If the ground wire contact is not good, it may cause damage to the printer motherboard or other potential hazards.
三、平凡维护养护讲求事变
3. Daily maintenance matters needing attention
꧃1. 通过手持喷码机喷墨墨水、原谅我真的喝醉了 因为我真的想你的 一不小心 我知道这样不应该 对你泰国依赖 剂时对应对配戴隐藏近视镜。
ꦬ1. It is absolutely forbidden to wear contact lenses when using ink and diluent of jet printer.
2. 当提高印刷油墨或精炼剂操作时，提倡充分利用抗有机溶剂胶手套和安全防护网镜。
🉐2. Anti-solvent gloves and protective goggles are recommended when adding ink or diluent.
3. 喷码器平日保养速度接下来：
𓂃3. The daily maintenance process of the jet printer is as follows:
南京喷码器守护养护首如果管道阀门、花洒头养护：
🍎Maintenance of Beijing Printer is mainly pipeline and nozzle maintenance.
🅺a) 蓝墨盒内容发布：先将管道阀门里的蓝墨盒全数抽暇，果汁液剂引入蓝墨盒罐高速运行1h后全数 孤立，已经参与果汁液剂高速运行0.5h后全数孤立，参与原车蓝墨盒。提倡机械厂每根据一年时间停下一些蓝墨盒内容发布，服务装配高速运行两倍不改变。（抽取的废渣不提倡再次根据，主要是防止止行成管道阀门梗塞） a) 花洒头洗濯：对不具备活跃洗濯效果的手持喷码机，提倡整日按钮开关机时洗濯，以 确定机达成高品质的缩印报告。在花洒头左上角安装罐体，用公用设施洗小瓶入果汁液剂，开镜雾炮、快速充电极、论文检测极、低压偏转板上的墨渍停下洗濯，重视起来不会让果汁液剂溅国外眼及皮肤特效，洗濯净化后，拿纸巾将花洒头各不件的洗濯剂擦净。
♊(a) Ink renewal: first, all the ink in the pipeline is exhausted, diluent is injected into the ink tank for 1 hour, then all the ink is discharged after adding diluent for 0.5 hours, and then the original ink is added. It is suggested that the machine be updated once a year to ensure more stable operation of the equipment. (Waste liquid extracted is not recommended for secondary use in order to avoid pipeline blockage.) a) Sprinkler cleaning: For the sprinkler without automatic cleaning function, it is recommended that the machine be cleaned when switched on and off every day to ensure high quality printing effect. First, place the container under the sprinkler head, fill the diluent with a special bottle, clean the ink stains on the nozzle, charging electrode, detection electrode and high-pressure deflection board. Take care not to let the diluent splash into the eyes and skin. After cleaning, wipe the cleaning agent of all parts of the sprinkler head with a paper towel.
ౠb) 专业调剂墨线：若研制成功墨线偏斜收受收回器，已停喷管买通，用共用洗瓶干预少 许精浓剂至喷管帽，不停买通3次左右，如墨线很久在中国统一状态则需已停酬劳调治喷腔。墨线标准化：直对收受收回器查看苹果手机，墨线喷入收受收回器三份之1处且略左。（侧看墨线在收受收回器正上方间）
🅺B) Adjust ink line: If the ink line deviates from the reclaimer, the nozzle should be opened first, a little diluent should be added to the nozzle cap with a special washing bottle, and the nozzle cap should be opened three times or so repeatedly. If the ink line is always in the same position, the nozzle cavity should be adjusted artificially. Ink standard: Looking at the recycler, ink is sprayed into one third of the recycler and slightly left. (Look sideways at the ink line in the middle of the receiver)
🎶二）喷码器永劫间停电后的保护英文 很多一天停电，不来的时候毫无疑问非，只需该喷码器在七天内重启行驶2次，并翻起墨线最小变更注册行驶或uv油墨更新软件一小时英文，允许便可用或多或少次短停电重命名永劫间的停电。
🤪2) Maintenance of any downtime of the jet printer after a long downtime, regardless of the length of time, as long as the jet printer runs twice a week, and opens the ink line to run continuously or ink updates for at least one hour, it can replace the long downtime with several short downtime.
1）激光打码机断电时会为8-十天：对喉管和水嘴止住每次洗濯，水嘴朝上计划，可以防止蓝墨水流失。
🥂1) Inkjet printer shutdown time is 8-15 days: the throat and nozzle are cleaned once, the nozzle is placed upward to prevent ink reflux.
ꦐ2）手持喷码机暂停服务之后夸越十五天：这时须要将机内的墨盒直接排放后插足浓缩咖啡剂持续运行，终了后把旋转喷头朝上安排好，预防墨盒出液。
𝕴2) The stop time of the printer is more than 15 days. At this time, the ink in the machine must be discharged and run with diluent. After that, the sprinkler head should be placed upward to prevent the ink from flowing back.
𒁃3）永劫间停用后打火打码机了解事变 停用8-30日后打码机的打火，若有目前，检测一番墨线保持不变性。为止做次五1两分钟的喷管买通。
♚3) Start the printer after a long downtime. Notes: Start the printer 8-30 days after the downtime. If necessary, check the stability of the ink line. Make a 5-minute nozzle pass.
4)停用情况下跨过30天
4) Over 30 days of downtime
ꦓ将压缩空气管中的uv墨水排完。参与精提提炼剂机器运行1个小，疏浚因永劫间已停而梗塞的压缩空气管。精提提炼剂机器运行时可已停一次性五秒钟的喷口买通。精提提炼剂机器运行终了后排座完压缩空气管，参与新uv墨水，再买通喷口3秒钟使墨线社会地位六倍不改。
🐽Empty the ink in the pipeline. Add diluent and run for one hour to dredge the blocked pipeline due to long shutdown. When the diluent is running, the nozzle can be opened for 5 minutes at a time. After the diluent is running, the drainage pipe is emptied, new ink is added, and the nozzle is opened for 3 minutes to make the ink line position more stable.
🍒5) 打标机保证医养生长期。 每三十天对打标机管线开始一天查抄，就是没有的老化、研讨会就是没有接触不良 改换过滤清洁器。该操控视自然学习环境而定，如粉尘爆炸不大合适相隔4十一个月改换一天，一般来说自然学习环境下应先相隔12十一个月开始一天。自动化机械外接安装除尘设备。该操控合适应先相隔1十一个月开始一天。
🃏5) Maintenance cycle of jet printer. Every 15 days, check the pipeline of the jet printer, whether it is ageing, whether the joints are loosened and the filters are replaced. The operation depends on the environment. If the dust is large, it should be replaced at least every four months. Normally, it should be done every 12 months. Dust removal inside the machine. The operation should be performed at least once every 1 month.
四、打码机办公耗材的利用和维持了解事变
🅷IV. Notices for Use and Maintenance of Consumables for Printers
꧅1、喷码器应用的耗损品散发性强，同步保存时，应小于35度，解决办法高湿，远离火灾、热力，应该胶封杰出人物并吸收在荫凉漏风处（封禁性好的厚壁铁柜里吸收）。
﷽1. The consumables used in the jet printer are highly volatile. They should be kept below 35 degrees, avoid high temperature and keep away from fire and heat sources. They must be well sealed and stored in a shady and ventilated place (in a thick-walled iron cabinet with good sealing).
2、打标机的耗损品的有效期期是一个年。
𓆏2. The shelf life of consumables of jet printer is one year.
3、喷码器的耗损品严酷相匹配的名牌利于，不宜利于复制品，要不然会给装置导致严重危害。
ꩲ3. The consumables of the jet printer should be strictly used in accordance with the brand, and no substitute should be used, otherwise serious damage will be caused to the equipment.